And let's do needlework with you ... remember, we have already begun to get acquainted with? Let's move on to practice today and consider the technique of papier-mâché from threads. To begin with, let's figure out how to make a cocoon of threads and think about what application it can find ... there are quite a lot of different master classes on this topic on the Internet ... I will tell you my approach to this type of creativity.
So let's get started...
In order to make a "cocoon" of threads using the papier-mâché technique, we need:
After we have prepared all the components, we proceed directly to creativity))) we thread the end of the thread from the coil (ball) into the needle and pierce the jar of glue, 
pull the thread through the glue, remove the needle 
Now we will wrap the ball with a thread, slowly pulling it through a jar of glue ... The thread itself will be smeared and saturated with glue))) 
How many threads do you need? According to your taste and desire))) It took me about two coils ... When you decide that the thread is enough - just cut it off ... if it seems to you that there is not enough glue on the thread, then take a regular brush and go over the surface of the cocoon with glue, just don't overdo it ))).
And forget about the craft until tomorrow ... let it dry thoroughly))) 
The cocoon has dried up ... it has become hard ... we take a needle and pierce the ball))). After that, we extract it from the cocoon ... 
my ball was torn into two parts ... I just pulled the first one out by the “tail”, and to get the second one you need to either find a place where there is a rather large gap between the threads or just make a hole with scissors. This is the basis of most papier-mâché thread crafts. That's how they do it And any interior crafts, toys .... my imagination, today, was only enough for a vase))).
We cut the cocoon into two unequal parts ... In principle, these details can already be adapted for a nest))) for .... 
or shove it in there)))….
but we'll move on...
and glue these two parts together, only upside down))) Actually, in the papier-mâché technique of threads, it is supposed to sew the parts together with a thread, but in this case I need the fastening to be “hard”, so I used glue pistol... 
It turned out a vase of threads ...
I didn’t think of anything smarter than how to cover the resulting vase with spray paint ... 
In my opinion, it turned out quite badly))) 
Hello dear readers! In today's master class, I want to tell you how to make a vase from threads. The process of making a vase will not take much time and effort, and the result will definitely please. Such a vase of threads, for sure, will simply fit perfectly into any interior and will arouse the interest of your guests ... Well, let's get started!
For work we need:
We cover the selected salad bowl with foil, bend the edges of the foil inside the plate.
We cut woolen threads, thread segments can be absolutely any (I cut about 20 - 30 cm each).
Pour PVA glue into a plate, in which we soak the cut pieces of threads.
We begin to apply the threads to the salad bowl covered with foil, you can stick the threads in a mess, as it turns out ... I tried to recreate something similar to the nest, so I glued the threads first across, then along.
When all the prepared threads are glued, leave the vase to dry. A vase of thread and glue will dry for about 24 hours.
After that, we remove the wicker vase from the salad bowl, and begin to carefully separate the foil from the threads. We begin to separate along the edges, in the direction from top to bottom, moving along the perimeter of the product.
When the foil is completely removed, we cover the surface of the table with newspaper, put the vase upside down, arm ourselves with a can of paint, and start spraying paint over the surface of the vase. By the way, a do-it-yourself vase made of threads looks much more spectacular with a glossy sheen, so it is better to purchase paint with shimmering particles (I used chrome paint).
When the paint dries, turn the vase upside down, and cover its inside with paint, then leave the product to dry again.
Since the thread vase is extremely light, it can be weighted with small pebbles or one large cobblestone, pre-painted to match the vase.
In such a vase you can store jewelry, knitting supplies, and simply use it as an independent, decorative item!
As a result of today's master class, we got a stylish vase made of threads and glue, covered with chrome paint, and also weighted with pre-painted cobblestone.
Additional master classes on making vases:
Master class: semolina decor or semolina vase.
Master class: how to decorate a vase with threads.
Dear readers, I hope you liked the vase of threads ... I'm waiting for your feedback in the comments. Do not forget to subscribe to receive news from the site, there will be a lot of master classes ahead.
Maybe we can take a break?
Show the answer to the riddle »
How to make a vase of threads with your own hands. Master Class.
Each needlewoman in the house has the remains of yarn and thread, which over time will definitely find a use, because many different crafts can be made from them.
Crafts from threads are soft, if you do not use glue or paste, or hard, and at the same time very light, airy and openwork.
For example, you can make an unusual openwork vase from threads.
Making a vase from threads with my daughter has long been in my needlework plans, but each time there were more urgent and important things to do.
And it is not known how long this idea would have remained unrealized if it were not for the themed surprise box "Bardabas". One of the crafts that was proposed to be made in our set was just such a vase.
And when all the necessary materials are ready, then half the battle is already, we can assume, done.
In the "Bardabas" set, according to the instructions for this craft, a slightly different version of the manufacture of this vase was offered - instead of glue, it was necessary to weld a paste.
My daughter and I worked with a paste for the first time, we liked the result - the product turned out to be very strong, keeps its shape well.
In such a vase, you can store balls with other threads, various little things, as well as sweets,
Easter eggs
or decorative eggs, also made of thread.
If desired, you can put a napkin, paper or fabric inside the vase.
Enjoy your creativity! Especially for readers of the blog "MORE creative ideas for children" (https://moreidey.ru), with sincere respect, Julia Sherstyuk
All the best! If the article was useful to you, please help the development of the site, share a link to this article in social networks.
Placing site materials (images and text) on other resources without the written permission of the author is prohibited and punishable by law.
moreidey.ru
DIY home decor is always beautiful, cozy and quite budget. Do you know that threads can not only sew or knit? It turns out that you can make original crafts for the home from them, which do not require special decorating skills and high costs. If you have a few balls of multi-colored thread lying around for a long time, use these inspiring ideas.
Light and balloons made of threads can decorate any interior. Making them is quite simple: you need to wind the threads smeared with glue around the balloon, then dry the threads, pierce the balloon and carefully remove it. To quickly learn how to make such stylish interior balls, watch the step-by-step video tutorial.
Another interesting idea is an elegant panel of threads stretched over small nails. Watch step-by-step photos or videos with a master class, and you can make such a panel yourself from the most available materials.
Thread pompoms are very easy to make and can be used to make fun and cozy decor items. Look at these photos - you will surely want to bring some soft and fluffy pom-poms to your interior...
With the help of threads, you can also create original vases. To do this, you will need a glass bottle (or jar), colored threads and PVA glue. Apply glue to the surface of the bottle, and then wind the yarn around the bottle as tightly as possible so that there are no gaps between the threads. Simple and beautiful!
To make bright interior letters from threads, you will need thick cardboard, scissors and threads of different shades. These letters can also be decorated with decorative beads, buttons or flowers. Multi-colored letters in the house can decorate a chest of drawers, a window sill, a shelf or a sofa.
With the help of threads, you can also make elegant wall decor. In terms of form and execution - there is scope for creativity and imagination! For example, it is a good idea to wind multi-colored threads on a regular embroidery hoop.
Or tie multi-colored threads of various lengths to a copper tube. See how easy it is to make such an accessory with your own hands - it turns out very stylish!
Mandala is a sacred geometric symbol used in meditation in Buddhism, which looks great in the interior as a decoration.
To weave such a mandala, you will need 8 identical sticks, multi-colored threads and scissors. There are several ways to weave a mandala, the easiest way is in the step-by-step photo below.
DIY simple panels: 7 master classes
10 DIY twine decor ideas
Photos: decorin.me, svadbalist.ru, etsy.com, pinterest.com, idesign.today
do it yourself, decor
kvartblog.ru
ya-superpuper.com
A house or apartment will look, seem or be perceived much more comfortable if you add a few do-it-yourself elements to the decor of the premises. After all, we all know for sure that everything that is done by hand, with soul, keeps the warmth of the master and, accordingly, looks much more interesting than soulless, serial, stamped compositions. Today, we will look at the step-by-step process of decorating a vase - with the most common threads. So, how to make a vase of threads? Master Class.
For work, you need to prepare the following items: a transparent glass vase (a tall glass or a jar of pickles), a disposable cup, a spool of thread, a stationery knife (or scissors), PVA glue, rhinestones, ribbon, a metal tag (optional, optional).
We take a disposable cup, with scissors, an awl or a needle we make two through holes from below (as in the photo).
We thread a thread into the holes formed, with which we will later decorate the vase. Then here, in a glass with a thread, pour PVA glue.
We begin to carefully wind the sewing threads on a glass vase. We wind in random order, freely crossing already pasted threads.
This is what a vase should look like, completely wrapped in threads. Next, the workpiece must be left for about a day, until the glue dries completely.
After the specified time has passed and the adhesive threads have completely dried, we tie the neck of the vase with any ribbon that matches the color.
In addition, the vase can be additionally decorated by sticking beautiful, shimmering rhinestones on its front part.
Now back to the ribbon, you can tie it with a single or double bow, or you can leave a simple knot. Our vase is tied with a bow with a metal tag with rhinestones (sold in sewing studios). And a white heart is pasted on the bow itself, also with a strazik.
Well, now we can sum up: we answered the question of how to make a vase from threads and showed clearly how to make it. 
As a result, we got a small, exclusive, blue vase (20 cm high), decorated with threads and rhinestones, which wonderfully complements the interior, giving warmth and positive emotions!
uytvdome.ru
DIY thread and glue vase
.jpg)
The master class is designed for preschoolers 6-7 years old, their parents and teachers.
Appointment. for interior design.
Tasks. develop the child's imagination, fantasy, fine motor skills, accuracy, form perseverance, the ability to bring work to its logical conclusion, the desire to work together with adults and other children. To acquaint parents, educators with the process of making a vase from threads.
For work we need:
1. Balloon
3. Thread "iris"
5. Sequins, glitter ribbon
.jpg)
1. Inflate the balloon, leaving the “neck” longer, and insert a test tube into it. (The test tube can be inserted after you wrap the entire ball with thread).
.jpg)
2. We pierce a bottle of PVA glue with a needle and thread as low as possible, after which we remove the needle. (The needle should be of such a diameter that the thread passes freely into the hole of the bottle, otherwise the thread will not be well saturated with glue).
.jpg)
3. We wind the thread around the ball. (It is advisable to grease the ball with cream, then the thread will not stick to it and it will be easier to pull out the ball).
.jpg)
.jpg)
4. The ball is ready. Now we tightly wrap the “neck” of the ball with a thread in a circle.
.jpg)
.jpg)
.jpg)
5. Using a needle, we pierce the ball and pull it out.
.jpg)
6. Carefully take out the test tube, apply glue to its bottom, return the test tube to its place and glue it. (If the vase is not stable, you need to flatten the bottom a little).
.jpg)
7. Decorate the vase with sequins, ribbon
.jpg)
8. Pour water into a test tube, put a sprig of viburnum in it and admire the bright colors of autumn!
Kalina, viburnum - a late berry.
Clusters, like beads in autumn.
There is nothing more delightful in Rus',
Participant of the professional competition for teachers "The Best Master Class"
fix-builder.ru
9. At the top of the thread egg, make a loop of ribbon so that it can be hung. A ball of thread can be carefully cut, as shown in the picture, bend the edges and get a flower bud.
Yes, yes, do not be surprised, it is from the threads. Moreover, they can be hung from the ceiling, put on the table and even make a lamp out of them (read the topic about lampshades with your own hands). All we need is PVA glue, balloons, threads, petroleum jelly, a needle, scissors, oilcloth.
After finishing the winding, cut off the thread and hide the tail under the turns. Wet the ball again with glue using a cotton swab or brush. The finished ball is left to dry for a day in limbo. After a day, we pierce the balloon with a needle and carefully remove it from the cobweb.
The shape of the ball or fingertip should be voluminous and oblong. It can be made from foil or cardboard with a pasted wrapper from delicious sweets. For the birds, we need two balls: one round, the second oblong. For flowers, you need to inflate and wrap small balls in diameter. We leave the smallest ones as they are - these will be the buds. From larger balls we form the flowers themselves.
Gently bend the edges outward and bend them slightly. The edges are messy, aren't they? We decorate them with airy lace in the color of the thread or braid. The ball is divided into two halves. But we cut the edges with an asterisk (this is how we usually cut a tomato to decorate dishes). We insert one half into the other, gluing them together with glue or double-sided tape.
And it’s so simple ... I’ve already come across something similar before (they did it in kindergarten, and they put rain inside), but I didn’t even know that it was possible to arrange it in such an original way. They are lightweight and can be hung up or made into a vase-shaped stand from a cut PET bottle.
We offer another craft from a series of budget decor ideas. These balls of thread are an easy, inexpensive, and beautiful way to decorate your home for the holidays without the need for special decorating skills or spending a lot of money. Step 3: Place the threads in the glue. It is better to do it in batches. Step 7: When the balloon has set (it should become firm and elastic), pierce the balloon with a needle and remove it from the balloon of thread. If the balloon is stuck on the edges, remove it with tweezers.
Such balls can be hung in the form of a garland, put in a basket or in a vase. You can also use balloons of various shapes and sizes. 213 Balls of thread can also be used to decorate a festive table or as decor for a party or a romantic dinner, both indoors and outdoors.
An egg made of threads will become a creative element of decor or an original gift. Let's consider in this article several ways to create crafts from nitoks with your own hands. 1. Inflate the balloon to the correct size. 2. The surface of the ball must be greased with a greasy cream or petroleum jelly. 4. Lubricate each layer of thread with glue. The transparency of the craft will depend on the number of layers and density.
6. The threads can be dyed with acrylic paints in any color. 7. Cut a hole in the side of the balloon. Decorate it with flowers or buttons. 4. The craft will consist of two parts, which then will need to be glued.
When the half is filled with threads, grease it with glue and leave to dry. 6. When the half dries, we release it from the mold and proceed to the manufacture of the second half. 3. We take a thread of any color. Hold the tip with your finger and wind the thread. It is not necessary to make the whole egg the same color. To make the craft more fun, use multi-colored threads. 4. Continue to grease the surface of the egg with glue and wind the threads to the very bottom. After that, leave the egg to dry.
With your own hands, you can make a lot of amazing things and crafts that will pleasantly surprise your relatives and friends. Use the tips from our articles and develop your skills in arts and crafts.
But to make it from threads and glue, in principle, like an ordinary slime, as they say, is as easy as shelling pears. We wind a thread dipped in glue on the ball, leave to dry. And now let's illustrate in a video how one pro makes a ball of thread. You can do it too once you get used to it.
kalavalapi.ru
The best gift, as you know, is handmade. One of the options for an original and beautiful gift for mom, girlfriend or good friend is a do-it-yourself vase. It will be an excellent decoration of the interior, bringing comfort and bright notes to it. This is much more interesting than a simple purchased vase. If you are on fire with the idea of making a vase with your own hands, then for you there are a few non-standard, but simple ideas that even small children can implement.
The first option is a vase made of paper. To do this, you will need any glass container. It can be a bottle or a jar. In addition, you will need corrugated multi-colored paper and decoupage glue, which must be diluted in a 1: 1 ratio.
First, cut your crepe paper the way you like it. It can be squares, rectangles or any arbitrary shape. Glue each piece of paper to the bottle so that the pieces overlap each other, and apply another layer of glue on top of the paper, which will not be noticeable after drying. Is the glue dry? Now cover the product with varnish to fix the result.
Such a vase is very simple, but it looks bright and original. If you don't have crepe paper, you can use magazine pages instead. It is better to choose the brightest, most colorful pages, which also need to be torn or cut into pieces.
A house or apartment will look, seem or be perceived much more comfortable if you add a few do-it-yourself elements to the decor of the premises.
After all, we all know for sure that everything that is done by hand, with soul, keeps the warmth of the master and, accordingly, looks much more interesting than soulless, serial, stamped compositions.
Today, we will look at the step-by-step process of decorating a vase - with the most common threads. So, how to make a vase of threads? Master Class.
For work, you need to prepare the following items: a transparent glass vase (a tall glass or a jar of pickles), a disposable cup, a spool of thread, a stationery knife (or scissors), PVA glue, rhinestones, ribbon, a metal tag (optional, optional). 
We take a disposable cup, with scissors, an awl or a needle we make two through holes from below (as in the photo). 
We thread a thread into the holes formed, with which we will later decorate the vase. Then here, in a glass with a thread, pour PVA glue. 
We begin to carefully wind the sewing threads on a glass vase. We wind in random order, freely crossing already pasted threads. 
This is what a vase should look like, completely wrapped in threads. Next, the workpiece must be left for about a day, until the glue dries completely. 
After the specified time has passed and the adhesive threads have completely dried, we tie the neck of the vase with any ribbon that matches the color. 
In addition, the vase can be additionally decorated by sticking beautiful, shimmering rhinestones on its front part. 
Now back to the ribbon, you can tie it with a single or double bow, or you can leave a simple knot. Our vase is tied with a bow with a metal tag with rhinestones (sold in sewing studios). And a white heart is pasted on the bow itself, also with a strazik. 
Well, now we can sum up: we answered the question of how to make a vase from threads and showed clearly how to make it. 
As a result, we got a small, exclusive, blue vase (20 cm high), decorated with threads and rhinestones, which wonderfully complements the interior, giving warmth and positive emotions!
To freshen up a familiar interior or decorate a house for the holidays, it is not necessary to make expensive purchases. Gossamer balls always look impressive as pendants, craft items, Christmas toys, vases and even chandeliers. Let's consider a simple way how you can make a ball out of thread and glue with your own hands.
The essence of making a gossamer craft lies in the technique of wrapping a ball shape with threads impregnated with an adhesive composition. The glue dries, the base is removed - the decoration is ready. Then the ball can be cut or decorated, combined into groups to create a composition, etc.
In order to make a ball of thread, first of all, you need to choose the right materials: yarn, glue, shape, glue container, brush, and prepare the workplace.
There are a few simple rules to keep in mind:
Consider the whole process step by step. It is simple, and it can take only 15-20 minutes to get the first blank.
Step 1. Let's choose a base. To do this, they most often use balloons of different diameters or fingertips (sold in pharmacies) - for small crafts. They are good because at the end of the work they are easy to take out: pierce them and, after the air has escaped, get them through the gap without damaging the shape of the threads.
Harder bases: rubber balls and foam balls (used most often for topiary), are perfectly rounded than inflatable forms. But at the same time, they are more difficult to extract at the final stage.
Step 2 Let's prepare the form. The base, which will be tied with threads, should easily lag behind the adhesive layer of the product after drying. To do this, the entire form should be coated with petroleum jelly or oil (from a pharmacy), or liquid silicone (inexpensive, in small jars or in the form of a spray, which is much more expensive, can be purchased at sports equipment stores or auto cosmetics). It is better to remove excess lubricant with a napkin so that the yarn does not slip off the surface during operation.
Step 3 We wrap the base. Threads well moistened in glue are placed randomly on the ball. It is advisable to do this so that the threads do not intersect in one place more than 2 times. You should not stretch the winding too much (especially on an inflatable base), but nothing should sag either. In places where there is not enough glue, you need to additionally apply it with a brush.
Step 4 Drying. At this stage of work, you need to let the whole craft dry. To do this, it is desirable to hang it in a dry and warm place so that it does not touch any surface (it will not stick). Depending on the size, thickness of the winding and humidity, the product can dry up to two days. To get the finished result much faster, it is permissible to use a hair dryer.
Step 5 We take out the base. After the ball is completely dry, you need to remove it from its original shape. If it is a balloon, then it is usually pierced and taken out through any suitable hole.
Step 6 We decorate. Any fairly light materials are suitable for decorating gossamer balls. These can be applications or inscriptions made of paper, beads, rhinestones, sequins, ribbons, etc. Balls collected in a group look spectacular. For example, for a New Year's wreath or garland.
The filling in balls will look beautiful: large beads, tinsel, serpentine, foil, confetti, etc. If necessary, the product can be painted. Aerosol paints are best for changing colors. With their help, it is easy to get shiny or matte gold and silver balls.
Advice! Hot glue is best for attaching jewelry: it is transparent, quickly hardens and gives a very strong connection.
A fairly dense ball of thread and glue can be used for topiary or other types of crafts. The main thing is that the fragile base can withstand additional decorative elements. Consider the technique of performing some of them.
You will need:
To assemble a pyramid of balls - a blank for a future toy - you need to lightly press on a larger ball from both sides to make neat dents. Glue a medium-sized ball to one of them, and place the other on the work surface. The third part (head) is also attached.
All remaining parts are glued to the finished base. At the end, you can tie a bright yarn scarf.
Advice! To make even dents on the ball, lightly moisten this place with a wet brush.
For its manufacture you need:
Making a topiary is not so difficult: just assemble the frame (attach the ball to the stick), place the “trunk” in the pot, fill it with filler and decorate.
Most often, crepe paper flowers, satin ribbon bows, coffee beans, beads, strips of quilling paper and much more are used for the “crown”. All this is attached to hot glue with a gun.
Making them is very easy. All that is needed is to cut the petals around the diameter of the ball with cloves. From one ball, 2 identical blanks are obtained. Flowers can be decorated with beads, beads, "stamens" made of wire, etc.
Since these crafts are very simple, they are great for competitions in kindergarten or for decorating a Christmas tree. For their manufacture, paper blanks of “wings”, “paws”, “tails”, “tufts”, etc. are needed, which are glued to the “trunk” - a ball of thread.
To get a vase or a deep plate from a gossamer ball, you need to carefully cut it in half. For the bottom, you need to slightly moisten the bottom and press it inward. When the product dries again, it will retain the desired shape.
To make the hemisphere of threads stronger, it is recommended to coat it on both sides with a colorless varnish. True, it will be possible to use such an item only for decorative purposes: it will not withstand moisture and a significant load. But at the same time it will become a highlight of any interior.
